Category Archives: Romantic Era

Men´s trousers 1840

This year we do again our history Sumer retreat. This time near Leipzig. As costume theme the romatic era would be suitable.

During the last years I made two Dresses for me, just a suit for the Gentleman is missing.

Let´s start with trousers. After some research it was clear I´ll sew checked trousers with a front fly. From 1830-40 front fall trousers became unfashionable. At the back they have a saddle like Jeans, a gusset and straps.

Unfortunately, I didn’t find pictures or anything else about pockets bags. So I decides to make them like Jeans pockets.

Let´s start with the pockets! The back pocket back gets a facing from fashion fabric and is joined to the front pocket back with a French seam.

Sew the front pocket back to the front trousers along the pocket opening, right sides together, trim seam allowances, turn inside out and press.

Sew the fly facing to the left front piece, prepare the buttonhole stand and sew five button holes. Pin the buttonhole stand to inside of the left front edge. Sew together with a curved seam from the right side.

Sew button stand to the right front edge.

Close pant legs and press. Close the crotch seam. Overcast all raw edges.

Insert gusset at the saddle.

For a clean finish the back seams are covered with a curtain.

The waistband is divided into two parts with a curved back edge.

Here you see the back straps with the buckle.

For the hem cut pieces of linen at the bias and baste to the inside along the hemline.

Make button holes at the corners of the pockets, close pockets with small covered buttons.

Finished!

Next time I´ll show you the making of the waistcoat.

19th century mitts

Next summer some friends of mine are going to organize an early 19th century costume ball. Of course a lady needs a pair of gloves to wear with her ball gown. But I don’t like gloves at all, so I decided to make mitts out of modern tights. I´ll show you my first attempt to sew a pair of mitts out of a cheap pair of tights.

First I thought a small size will be perfect to fit my arm, but it seemed to be a little bit too bulky at the wrist, so I had to make them tighter and ad a seam at the hand edge. I sewed all seams with a normal sewing thread and a normal sewing needle by hand.

All seams are sewn quite loose respecting the elasticity of the material. To give more stability to the seams they are sewn twice.

On the whole it worked better than I thought. Next time I´ll try it with tights with a looser pattern.

Making-of my 1830 Dress Part 3 The Skirt

The original skirt is made from georgette, I don´t know if there is a sateen layer underneath, but it looks like.
For the skirt panels I took three times my waist plus 2cm for the underlap at the back. If you are quite thin (thinner than me, my waist measurement with the corset is 78cm) you should take more to reach the desired diameter of the seam.
I sewed togehter the skirt panels first and made a slash at the center back, folded in the raw egdges and stitched them down. Why I didn´t used a seam at the center back? Because so I would have a visible seam at the front side.

I made 7 folds each side, opening to the back, shift the edges to form a curved waistline

Sew the skirt to the bodice. The picture shows how it looks like at the center back.

Trim the seam allowance at the waistline, fold it into the bodice and stitch down, catch only the lining.

Fold in the fabric along the hemline. The skirt should end about 10cm from the floor at the ankle. You would wear ballerina shoes with that dress. I decided to sew my hem with small stitches from the right fabric side, because the original dress has a visible hem stitching line, not even tried to be covered with the trimmings and I was aware the sateen fabric doesn´t tolerate a hem stitch.

For the belt I took one layer of sateen and one layer of cotton fabric, the edges neatend with bias binding. The belt is closed with hooks and sewn eyes. Finally a large bow is attatched.

That´s the finished dress. Excuse the picture but the dress doesn´t fit the dress form quite well and I just made a quick picture of the finished dress to show you.

Go to Part 1 or Part 2

Making-of my 1830 Dress Part 2 The Sleeves

I think that sleeves are the most exiting sleeves I´ve ever seen. Some years ago when I started to sew historical clothing I couldn´t imagine to wear dresses from the romantic era or the 1880´s. At that time, I even decided never to sew dresses from that eras. I don´t know what happened, but I changed my mind and made some 1880´s dresses and I loved them! Searching the internet for inspiration I found the dress from the LACMA and felled in love with it! Let´s start sewing the sleeves!

The sleeve pattern itself isn´t anything special. It´s just a pattern you would use to sew a puffed sleeve, it´s all about the folds! I´ll show you on a paper model. The length of the upper sleeve edge has to be the length of the underarm part where you don´t have folds, plus the upper part with the folds multiplied by 5. Length of upper edge = (2 x a) + (2 x b x 5). We have 15 folds, so depth of one fold is (2 x b) : 15

First fold your sleeve lengthwise to the half, wrong sides together and press a little bit, not too strong because later on you don´t need that fold. You have calculated the depth of the folds before, now fold the double layer of fabric overlapping as shown and press.

Open the sleeve and lay it flat on a table. At all “hills” you mark 1,5cm from the half-line and fold diagonal “hills”-folds with the help of the iron. The 2nd picture shows how it looks like on fabric.

Close the fold´s again along the upper edge. Shift all corners to give the edge a straight finish, so the sleeve opens better when finished. Baste all folds in place. Do the same with the lower edge, it´s just the opposite direction to lay the folds.

Sew a piped band to the lower edge of the sleeve

Insert the sleeve into the armhole. Add lace along the bottom edge.

Attatch thin tapes, about 15cm long, to the highest shoulder point and to the inside of the sleeve tape vis-a-vis the sleeve seam. Tie the tapes to loop up the sleeve as desired.

Got to Part 1 or Part 3

Making-of my 1830 Dress Part 1 The Bodice

Do you know the 1830 dress from the LACMA? I´m talking about the pink evening dress with that amazing sleeves: 1830 Evening Dress
Fashion plates too show dresses with that kind of sleeves. But how to make them? The pictures from the LACMA really have a high resolution, but doesn´t show every detail to understand the sleeves.
Finally I found this pictures: 1st 2nd
They gave me all Information I needed!

The fabrics used to make the original dress are silk sateen and silk organza. This are informations from the museum homepage. I think a silk georgette was used, because the fabric is less transparent than organza would be.

I think the sleeves are made from sateen covered with georgette, I´m not sure if the skirt is made the same way. For the bodice stripes of fabric, cut on the bias, are mounted. First I thought they where mounted on a cotton bodice, like later dresses would be, but it seems that the lower part of the bodice is just made from georgette. Neckline and armhole are piped.

I decided to use a basic bodice made from glazed Cotton to mount the stripes. The pattern I took from my 1845 dress. The dress fits quite well so I didn´t had to made any alterations.

I decided to make the dress from sateen in ivory and burgundy. Why I didn´t used a georgette? Because I was a little bit under time pressure to finish the dress and there was no time left to find a matching georgette,

Let´s start sewing! Just close the darts and the shoulder seams. Cut the darts and press for less bulk. Turn in and topstitch facings at the center back, allow 2cm at the left side for a underlap.

Wrong side up attach a 2″ wide facing around the neckline.

Sew your piping around the neckline. Trim the seam allowance of the bodice, the facing and the inner seam allowance of the piping. Nocht the seam allowances at the center front. Fold the upper seam allowance from the piping around and sew just to the cotton bodice. Fold over the facing at the back and stitch down.

Prepared bias straps in ivoy and burgundy, folded lenghtwise, wrong sides togehter and pressed, width is now 5cm. The 2nd picture shows the straps pinned to the bodice to see how it looks like. Decided to make the straps 3cm at the shoulderand 2cm wide at the center front.

The first ivory strap is folded open and sewn to the bodice along the neckline. As you can see I shifted the shoulder point to the front, to the highest point of the shoulder. Then I sewed the strap along the bottom edge to the basic bodice.

The 2nd strap in burgundy is sewn to the basic bodice just along the bottom edge. The top edge is left loose. Give the straps enough room for the breast. Don´t make thight stitches. At the center front fix straps with some stitches.

In the sam way sew the rest of the straps to the bodice. The lowermost piece is cut on the bias too, then pinned to the bodice. Draw the outline directly on the fabric incl. 1cm seam allowance at the top edge and cut out. Fold in the seam allowance at the top edge and sew to the 5th strap. Baste along the remaining edges to the basic bodice.

At the back sew straps to the bodice in the same way, overlap 1cm at the shoulders. At the left side mark center back (underlap is 2cm) and attatch eyelets first. At the right side form an overlap with the straps. Hooks can be attatched later. Sew along the right center back with small stitches through all layers.

Sew piped epaulettes, 1cm wide. This is quite tricky and I have no idea to make it better then shown below. Before you sew the epaulettes to the shoulders pull out the piping and cut off the seam allowance to avoid bulk. Sew the epaulettes to the highest point of the shoulder covering the raw edges of the straps.

Before closing the side seams attatch a piping band to the armhole. Trim inner seam allowances, fold over the outmost and sew to the bodice like you did before with the neckline.

Next time I´ll show you the sleeves… Part 2

BlackSnails Sewing Blog

Sewing Projects and Tutorials